Understanding Plumbing Basics When Installing a Bathtub
Understanding Plumbing Basics When Installing a Bathtub
Blog Article
Have you been trying to find information and facts on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't exactly brain surgery, however it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably hard task. If the old tub is readily easily accessible, the job can relocate speedily; if you need to open up a wall to eliminate the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make sure you have actually certified yourself for the job as well as are comfortable attempting it. Rather than employing a professional to take over a halfway-completed project, it is better to think about using one prior to you start. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly assist you mount a brand-new bath tub in your bathroom if you have actually currently bought a brand-new bathtub and also do not need to change the setup of your previous supply of water pipelines.
Your devices and also material checklist ought to comprise the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bath should be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the restricted access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, position the tub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the tub until the level checks out degree.
To mount faucets, fit all-time low of the outermost flexible faucet connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leakages.
Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub must wait up until the bath tub has been used at least once as this will resolve it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Safeguard the faucet in place with the producer provided backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, creating the water to permeate the wall between the bathroom and the tiling, causing complications with dampness as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes and cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can break rather very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads on A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of content was sensible. Enjoyed reading our post? Please share it. Help other people find it. Thank-you for taking the time to read it.
Ring, relax, resolved! Report this page